高压电缆附件/ High voltage cable accessories

用于交联电缆的硅橡胶复合套户外终端 - XLPE silicone outdoor termination

产品特点：

- 质轻
- 易于安装
- 抗紫外线辐射
- 防水
- 防爆
- 抗震
- 在许多国家和气候带的良好业绩记录
- 已超过25年的杰出运行经验

用于交联电缆的硅橡胶复合套终端的特点，是采用整体预制的硅橡胶预制应力锥。
终端套管的爬距可以根据应用、顾客的需要和不同气候带的需求而确定。
所有的终端都是依据IEC60840 ( ≤ 170kV) ，IEC62067 ( >170kV）,

IEC60071 （绝缘配合）或IEEE Std48-1996等国际标准设计和检验的。

由于硅橡胶复合套户外电缆终端头所拥有的上述优点，我们的硅橡胶复合套电缆终端头专为各种型号或其它电缆厂商的交联电缆设计，

电压范围从72.5kV至550kV，适用电缆截面最大可2500mm2。

Product features:

-  Light weight

-  Easy to handle

-  Outstanding UV
-  Excellent hydrophobic properties

-  Explosion proof

-  Many references in different countries and climate zones
-  Over 25 years of outstanding operation experience

Silicone rubber compound sleeve terminal used for XLPE cable is that the stress cone of the silicone rubber prefabricated as a whole is used.
The climbing distance of the terminal casing can be determined according to the application, customer needs and different climatic zones.
All terminals are based on IEC60840 (≤ 170kV), IEC62067 (>170kV),designed and tested to  IEC60071 (insulation fit) or IEEE std48-1996.

Based on the outstanding properties of the prefabricated and electrically tested one-piece slip on stress cones,

the reliable modular construction of the termination allow it’s application to all types of polymeric insulated cabless.

The voltage range ranges from 72.5kv to 550kV, and the maximum cross section of applicable cable up to 2500mm2.

用于交联电缆的GIS终端 - XLPE GIS termination

用于交联电缆的GIS电缆终端，采用环氧树脂套管，专用于和SF6气体绝缘开关（GIS）连接。

它们的主要优点有：

- 质轻

- 易于安装

- 对所配套安装的电缆没有过高的要求

- 在很多国家和气候带有优良的业绩记录

- 已超过30年的杰出运行经验

用于交联电缆的GIS终端的特点，是采用整体预制的硅橡胶预制应力锥。

所有终端都是按照IEC62271-209(GIS标准）IEC 60840 (≤170 kV), IEC 62067 (>170kV),

IEC 60071 (绝缘配合)或是IEEE Std 48-1996等国际标准设计和检验的。

由于GIS电缆终端头所拥有的上述优点，我们的GIS电缆终端头专为各种型号

或其它电缆厂商的交联电缆设计，电压范围从72.5kV至550kV，适用电缆截面最大可达2500mm2。

Product features:

-  Light weight
-  Easy to handle
-  There are no excessive requirements for cable installed

-  Many references in different countries and climate zones

-  Over 30 years of outstanding operation experience

The GIS terminal used for crosslinking cable is characterized by the prefabricated stress cone of silicon rubber.

All terminals are in accordance with iec62271-209 (GIS standard) IEC 60840 (≤170 kV), IEC 62067 (>170kV),

IEC 60071 (insulation fit) or IEEE Std 48-1996 and other international standards for design and inspection.

Due to the above advantages of GIS cable terminal head, our GIS cable terminal head is designed for various models

The voltage range ranges from 72.5kv to 550kV, and the maximum cross section of the applicable cable can reach 2500mm2.

交联电缆干式插拔GIS终端/变压器终端 - XLPE dry-type plug-in GIS/Transformer termination

布鲁克干式插入式GIS/变压器电缆终端可用于高达300kV的高压电气系统。

它们的主要优点有：

-    质轻
-    易于安装
-    可以将电缆直接穿入GIS内，不需要增加额外工作量（如对SF6气体的收放）
-    电缆和终端的安装与GIS的安装可分开进行

与传统充油GIS终端相比较而言，干式插拔GIS终端应力锥对保持电场梯度更为重要。
高品质应力锥对终端的长期可靠运行至关重要,干式插拔GIS终端采用的整体预制式应力锥性能优良。
干式插拔GIS终端的设计突出特点,是能够与各种型号的GIS相配套，让用户更加自由选择。
终端都是按照IEC62270-209(GIS标准),IEC60840 (≤170kV),IEC62067(＞170kV),

IEC60071(绝缘配合)及IEEE Std48-1996等国际标准设计和检验的。

基于上述优点,我们的干式插拔GIS终端专为各种型号电缆计，适用最高电压为300kV，适用电缆截面最大可达2500mm 。

Product features:

-  Light weight

-  Easy to handle

- Cable can be directly threaded into GIS equipmenr without additional workload (e.g. SF6 gas withdrawal or discharge)
- Cable and terminal installation can be done separately from GIS installation

Compared with traditional oil-filled GIS terminations,

the stress cone of dry plug GIS terminals is more important to maintain the electric field gradient.

High quality stress cone is crucial to the terminations long term reliable operation,

the whole prefabricated stress cone used in GIS terminal has excellent performance.

The design of our dry plug and pull GIS terminal is characterized by its matching with various models of GIS.

All terminals are designed and tested in accordance with international standards such as:

IEC62270-209 (GIS standard),IEC60840 (≤170kV),IEC62067(> 170kV),IEC60071(insulation fit) and IEEE std48-1996.

Our dry plug and pull GIS terminal is specially designed for various types of cables and other cable manufacturers.

The highest applicable voltage is 300kV and the maximum applicable cable section is up to 2500mm.

用于交联电缆的变压器终端 - XLPE transformer termination

用于交联电缆的变压器电缆终端，采用环氧树脂套管，专用于和变压器连接。

它们的主要优点有：

- 质轻
- 易于安装
- 对所配套安装的电缆没有过高的要求
- 在很多国家和气候带的优良的业绩记录
- 已超过30年的杰出运行经验

用于交联电缆的变压器终端的特点，是采用整体预制的硅橡胶预制应力锥。

所有终端都是按照IEC 60840 (≤170 kV), IEC 62067 (>170 kV), IEC 60071 (绝缘配合)

或是IEEE Std 48-1996等国际标准设计和检验的。

注意：变压器终端的屏蔽罩是根据用户要求专门设计的，需要时请向我们单独订购。

由于变压器终端头所拥有的上述优点，我们的变压器终端头专为各种型号或其它电缆厂商的交联电缆设计，

电压范围从72.5kV至550kV，适用电缆截面最大可达2500mm 。

Product features:

-  Light weight

-  Easy to handle

-  There are no excessive requirements for cable installed

-  Many references in different countries and climate zones

-  Over 30 years of outstanding operation experience

The transformer terminal of the crosslinked cable is characterized by the prefabricated stress cone of silicon rubber.

All terminals are in accordance with IEC 60840 (≤170 kV), IEC 62067 (>170 kV), IEC 60071 (insulation fit).

Or international standards such as IEEE Std 48-1996.

Note: the corona shielding of the transformer terminal is specially designed according to the requirements of the user.

Our transformer terminal heads are specially designed for cross-linking cables of various types or other cable manufacturers.
The voltage range ranges from 72.5kv to 550kV, and the maximum cross section of applicable cable up to 2500mm.